Asia-Pacific ยท Glass Manufacturer
KCC Glass: Window Cleaning Guide
๐ฐ๐ท South Korea ยท Last reviewed by Justin Orloff
ENKOํ๊ตญ์ดFor owners, installers and cleaners looking after KCC Glass windows. The maker's own care advice first, then what I add as a window cleaner since 1999.

Quick Facts
- Founded
- 1958
- HQ
- Seoul, South Korea
- Materials
- Float glass, Low-E glass, laminated glass, tempered glass
- Specialty
- Architectural and automotive glass production; Klenze premium window brand
- Market
- South Korea construction and automotive; international export
Brand at a Glance
- One of South Korea's largest flat glass producers supplying construction and automotive sectors
- Klenze brand represents KCC Glass in the premium residential window market
- Low-E, laminated, and tempered glass units specified across Korean residential and commercial construction
- Official website
- www.kccglass.co.kr
Product Range
- Float glass base product for downstream processing and fabrication
- Low-E coated glass for energy-rated insulated glazing units
- Laminated safety glass for structural, facade, and overhead glazing
- Tempered glass for shower enclosures, balustrades, and entrance systems
- Klenze premium residential window units
Why This System
KCC Glass supplies the glass element - the performance component inside the frame system. Their Low-E coatings are applied to the inner surface of insulated units and are not reachable for cleaning, but the outer glass surface still requires correct care: neutral pH, no abrasives, no tools that scratch the surface and scatter light through the coating stack. On Klenze-branded residential windows, the glass specification is typically high-performance double or triple glazing with Low-E inner panes.
Korean construction sites and urban environments deposit a complex mix of pollution, yellow dust, and construction residue on glass. KCC Glass coated units require pH-neutral cleaning - alkaline construction site cleaners or acid-based descalers will etch the glass surface or attack spacer bar coatings at the unit edge over time. Yellow dust season demands pre-rinsing before squeegee work: dry particulate ground into coated glass creates micro-scratches that scatter light and reduce coating clarity.
Step 1 of 2: Manufacturer Recommendations
Official Care Guidance
No official guide published. The steps below are based on Justin Orloff's hands-on experience since 1999 with this system.
Step 2 of 2: The Orloffs Protocol
The Orloffs Protocol
Since 1999 I've cleaned hundreds, if not thousands, of different window brands and systems. The physics of clean glass don't change from one brand to the next. Follow the steps below and you'll clean your KCC Glass windows to a professional standard, guaranteed.
Follow these steps in order. Each one builds on the last. This is the same sequence I use on every KCC Glass installation.
Pro Tools
My daily tool list. This is what I carry to every job.
- 1Microfiber T-bar applicator, kept clean and rinsed regularly to prevent grit
- 2Professional squeegee with a fresh rubber blade
- 3Extension pole for glass above arm height
- 4Bucket with at least 10 litres of water and enough soap for cleaning power without excess foam
- 5100% cotton towelling rags for edge detailing
- 6Vacuum for sill tracks and base profiles
Preparation: before any water touches the glass
Fill the bucket with at least 10 litres of water. Add soap for cleaning power: enough to cut through environmental deposits, not so much you are fighting foam.
Before touching the glass, brush down the surface to remove loose dust, spiderwebs, and debris. Any grit left on the glass during the wash phase risks scratching during agitation.
Check the glass frame condition before you start. Confirm which cleaning product is safe for that surface before opening any bottle.
Cover anything below the windows that cannot be moved.

Agitation: apply and work the solution
Dip the microfiber T-bar completely into the soap water, both sides. Remove excess water with your hand so it does not drip. Apply the solution across the entire glass surface with overlapping passes.
The goal is to fully dissolve and release every deposit from the glass surface. Anything not released during agitation gets transported across the glass by the squeegee as a smear.
For stubborn spots (insect marks, salt residue, environmental deposits), re-apply soap water and allow it to soak for a full minute before agitating again. Use more soap water, not more pressure.
For panels above arm reach: attach the T-bar to an extension pole. Work in sections (top first, then middle, then bottom), keeping each section wet until you squeegee it.
Rinse the T-bar cover regularly during the job. A dirty applicator causes microscopic scratches that accumulate over time.

Detail the frame edge before squeegeeing
Use your 100% cotton towelling rag, finger pressed into the fabric, to work into every junction and remove pooled soap water before the squeegee pass.
This prevents drips running down onto already-cleaned areas during squeegeeing and keeps soap water out of drainage channels.
On KCC Glass glass frames, pay particular attention to the bottom edge where glass meets the frame sill: water pooled here runs into drainage openings and leaves residue over time.

The squeegee
Tilt the squeegee at a slight angle so soap water spills from one side of the channel only, not both. If the rubber is jumping or squeaking, either the rubber is not lubricated enough or the glass surface has warmed.
Cutting in: start with the rubber blade making first contact on a dry edge of the glass.
Side to side: horizontal passes across the panel. Works well on wide sections. Top to bottom: vertical passes down the panel. Works well on tall narrow sections.
The J turn: one smooth unbroken motion top to bottom, wrist rotating at each end to reverse without lifting the rubber. The most efficient method on larger panels, but it requires training before applying it to premium glass.
Wipe the rubber dry after every pass. Overlap each stroke by 2-3 cm.

Final edge detailing
After squeegeeing, there is always a residual line of water along the bottom edge and at the panel sides. Take a dry cotton rag, fold to a clean corner, and detail these edges in one smooth pass.
On KCC Glass frames, the bottom edge where glass meets the sill requires the most careful attention. Water left here runs into drainage and leaves residue that affects the next clean.
Rotate the rag to a clean section after every pass. If the rag picks up grit at any point, replace it immediately.

Frame wipe and hardware check
On glass from KCC Glass: use pH-neutral solution only on all coated surfaces. Any coating damage (Low-E, self-cleaning, solar control) is permanent and the unit must be replaced.
Check that all drainage openings are clear and unobstructed. Water must be able to flow freely: a blocked channel leads to accumulation that affects seal performance over time.
Operate every opening window through its full range. Stiff handles or resistance at locking points indicate hardware that needs lubrication. Flag it to the owner rather than forcing it.

Pro Tips
- KCC Klenze units often have a slight tint or coating sheen - check your squeegee angle in direct light to confirm no streaking from an inconsistent blade pass.
- Never use metal scrapers on KCC coated glass even for stubborn residue - request chemical spotting solution appropriate for coated glass.
- On high-rise facades with KCC supplied curtain wall glass, check for sealant smearing around unit perimeters - construction sealant is a common post-handover soiling type and requires a dedicated sealant remover, not standard detergent.
What NOT To Do
- Do not use alkaline or acid-based cleaners on KCC coated glass units.
- Do not use abrasive pads or scrapers - coated glass is more vulnerable to surface scratching than standard float glass.
- Do not clean during or immediately after yellow dust falls without pre-rinsing - dry particulate on the glass surface causes scratching under the squeegee.
Bundle Kit
Pro Kit
The full professional setup. Brass squeegees, T-bar with applicator cover, tool belt, rags, soap, and bucket. Everything from the daily tool list in one box.
Cleaning Frequency
Every 6-8 weeks in urban Seoul environments. Monthly during yellow dust season. New-build handover cleaning should be treated as a separate project from ongoing maintenance - construction residue requires different products and significantly more time.
Frequently Asked Questions
How often should I clean KCC Glass windows?
For KCC Glass windows, Every 6-8 weeks in urban Seoul environments. Monthly during yellow dust season. New-build handover cleaning should be treated as a separate project from ongoing maintenance - construction residue requires different products and significantly more time.. City locations may need more frequent cleaning.
What tools do I need for KCC Glass windows?
Professional cleaning of KCC Glass windows requires my daily tool list of: Microfiber T-bar applicator, kept clean and rinsed regularly to prevent grit, Professional squeegee with a fresh rubber blade, Extension pole for glass above arm height, Bucket with at least 10 litres of water and enough soap for cleaning power without excess foam, 100% cotton towelling rags for edge detailing, Vacuum for sill tracks and base profiles.
What should I avoid on KCC Glass windows?
Do not use alkaline or acid-based cleaners on KCC coated glass units.
Does KCC Glass publish an official cleaning guide?
KCC Glass has not published an official cleaning guide. The protocol on this page is based on Justin Orloff's hands-on experience since 1999.
Can I use a water-fed pole on KCC Glass windows?
In my experience, yes: purified water via a water-fed pole is one of the safest methods for KCC Glass glass. Ensure TDS is at or near zero before use and avoid directing high-pressure water at seals or gaskets.
Field Notes
โOn Korean high-rise projects where KCC glass has been specified for curtain wall panels, the primary post-construction cleaning challenge is construction adhesive and cement haze on the glass surface. Cement haze on coated glass requires a dilute acid-gel product applied carefully, not mechanical scrubbing. Always test on a non-visible panel section first and confirm product compatibility with KCC glass coating types before treating a full elevation.โ
What's next for you?
The Skill
New to window cleaning?
Start with the core techniques before tackling premium systems.
Start The Skill, $69The Standard
Upskill your team
Covers every system, product type, and tricky scenario.
Train your team, $199 per personDo you make windows, doors or glazing?
The brands here are not partners. We wrote these care guides ourselves, so your customers know how to look after your windows. Want your own?
Become a Brand PartnerBrand logos provided by Logo.dev