Skip to content
svenska-fonster logo

Europe · Window Manufacturer

Svenska Fönster: Window Cleaning Guide

🇸🇪 Sweden · Last reviewed by Justin Orloff

For owners, installers and cleaners looking after Svenska Fönster windows. The maker's own care advice first, then what I add as a window cleaner since 1999.

See the 6 steps

A squeegee pulling soap water off a window, with a harbour behind the glass

Quick Facts

Founded
Established Swedish manufacturer
HQ
Edsbyn, Sweden
Materials
Wood and wood-aluminium composite
Specialty
Renovation and new-build windows
Market
Scandinavia (Dovista/VKR Group)

Brand at a Glance

svenska-fonster windows
Part of Dovista/VKR Group - Europe's largest window group
Wood and wood-aluminium systems for renovation and new build
Strong reputation in Swedish renovation market
Official website
www.svenskafonster.se

Product Range

  • Wood casement and tilt-and-turn windows
  • Wood-aluminium composite windows
  • Renovation window systems

Why This System

Svenska Fönster windows appear in both new builds and renovation projects - which means you'll encounter them in a range of property types and ages. The renovation range is designed to fit older Swedish opening sizes, which can mean non-standard dimensions and hardware from mixed eras.

Renovation installations often mix old masonry reveals with new frames, creating ledges and junctions that trap debris and moisture. On wood frames, Orloffs apply the same careful approach as all Nordic timber systems - low pressure, soft brushes, minimum water contact. On wood-alu renovation windows, the aluminium outer is more forgiving but still needs appropriate cleaning products.

Step 1 of 2: Manufacturer Recommendations

Official Care Guidance

No official guide published. The steps below are based on Justin Orloff's hands-on experience since 1999 with this system.

Step 2 of 2: The Orloffs Protocol

The Orloffs Protocol

This is how I clean Svenska Fönster windows. The tools and technique below come from daily professional work on the glass since 1999. Every step has been tested on real installations and adapted specifically for Svenska Fönster systems.

Follow these steps in order. Each one builds on the last. This is the same sequence I use on every Svenska Fönster installation.

Pro Tools

My daily tool list. This is what I carry to every job.

  1. 1Microfiber T-bar applicator, kept clean and rinsed regularly to prevent grit
  2. 2Professional squeegee with a fresh rubber blade
  3. 3Extension pole for glass above arm height
  4. 4Bucket with at least 10 litres of water and enough soap for cleaning power without excess foam
  5. 5100% cotton towelling rags for edge detailing
  6. 6Vacuum for sill tracks and base profiles
  1. Preparation: before any water touches the glass

    Fill the bucket with at least 10 litres of water. Add soap for cleaning power: enough to cut through environmental deposits, not so much you are fighting foam.

    Before touching the glass, brush down the surface to remove loose dust, spiderwebs, and debris. Any grit left on the glass during the wash phase risks scratching during agitation.

    Check the aluminium frame condition before you start. Confirm which cleaning product is safe for that surface before opening any bottle.

    Cover anything below the windows that cannot be moved.

    Window cleaning tools laid out ready: squeegee, brass channel and washer sleeves
  2. Agitation: apply and work the solution

    Dip the microfiber T-bar completely into the soap water, both sides. Remove excess water with your hand so it does not drip. Apply the solution across the entire glass surface with overlapping passes.

    The goal is to fully dissolve and release every deposit from the glass surface. Anything not released during agitation gets transported across the glass by the squeegee as a smear.

    For stubborn spots (insect marks, salt residue, environmental deposits), re-apply soap water and allow it to soak for a full minute before agitating again. Use more soap water, not more pressure.

    For panels above arm reach: attach the T-bar to an extension pole. Work in sections (top first, then middle, then bottom), keeping each section wet until you squeegee it.

    Rinse the T-bar cover regularly during the job. A dirty applicator causes microscopic scratches that accumulate over time.

    Washing the glass with a soaked sleeve to lift and release the dirt
  3. Detail the frame edge before squeegeeing

    Use your 100% cotton towelling rag, finger pressed into the fabric, to work into every junction and remove pooled soap water before the squeegee pass.

    This prevents drips running down onto already-cleaned areas during squeegeeing and keeps soap water out of drainage channels.

    On Svenska Fonster aluminium frames, pay particular attention to the bottom edge where glass meets the frame sill: water pooled here runs into drainage openings and leaves residue over time.

    Detailing the frame edge with a cloth before the squeegee pass
  4. The squeegee

    Tilt the squeegee at a slight angle so soap water spills from one side of the channel only, not both. If the rubber is jumping or squeaking, either the rubber is not lubricated enough or the glass surface has warmed.

    Cutting in: start with the rubber blade making first contact on a dry edge of the glass.

    Side to side: horizontal passes across the panel. Works well on wide sections. Top to bottom: vertical passes down the panel. Works well on tall narrow sections.

    The J turn: one smooth unbroken motion top to bottom, wrist rotating at each end to reverse without lifting the rubber. The most efficient method on larger panels, but it requires training before applying it to premium glass.

    Wipe the rubber dry after every pass. Overlap each stroke by 2-3 cm.

    Pulling the squeegee across the wet glass in one clean stroke
  5. Final edge detailing

    After squeegeeing, there is always a residual line of water along the bottom edge and at the panel sides. Take a dry cotton rag, fold to a clean corner, and detail these edges in one smooth pass.

    On Svenska Fonster frames, the bottom edge where glass meets the sill requires the most careful attention. Water left here runs into drainage and leaves residue that affects the next clean.

    Rotate the rag to a clean section after every pass. If the rag picks up grit at any point, replace it immediately.

    Wiping the final edge of the glass with a dry cloth
  6. Frame wipe and hardware check

    On Svenska Fonster powder-coated aluminium frames: use pH-neutral cleaner only, never abrasive pads or steel wool. Dry immediately after wiping.

    Check that all drainage openings are clear and unobstructed. Water must be able to flow freely: a blocked channel leads to accumulation that affects seal performance over time.

    Operate every opening window through its full range. Stiff handles or resistance at locking points indicate hardware that needs lubrication. Flag it to the owner rather than forcing it.

    The finished, streak-free window after the full Orloffs Protocol

Pro Tips

  • Renovation properties often have old putty or mastic at the masonry-frame joint - do not disturb or clean aggressively around these
  • Swedish summer UV is intense - don't leave cleaning solution on frames in direct sun
  • Check tilt-and-turn hardware on older installations - hardware may be from a previous window generation

What NOT To Do

  • Do not use solvent cleaners near mastic or sealant joints in renovation installations
  • Do not apply pressure to old casement hardware - test before operating
  • Do not use abrasive pads on any painted timber surface

Bundle Kit

Pro Kit

The full professional setup. Brass squeegees, T-bar with applicator cover, tool belt, rags, soap, and bucket. Everything from the daily tool list in one box.

Cleaning Frequency

Twice yearly - spring and autumn. Renovation properties may need gutters and reveals cleaned at the same visit.

Frequently Asked Questions

How often should I clean Svenska Fönster windows?

For Svenska Fönster windows, Twice yearly - spring and autumn. Renovation properties may need gutters and reveals cleaned at the same visit.. City locations may need more frequent cleaning.

What tools do I need for Svenska Fönster windows?

Professional cleaning of Svenska Fönster windows requires my daily tool list of: Microfiber T-bar applicator, kept clean and rinsed regularly to prevent grit, Professional squeegee with a fresh rubber blade, Extension pole for glass above arm height, Bucket with at least 10 litres of water and enough soap for cleaning power without excess foam, 100% cotton towelling rags for edge detailing, Vacuum for sill tracks and base profiles.

What should I avoid on Svenska Fönster windows?

Do not use solvent cleaners near mastic or sealant joints in renovation installations

Does Svenska Fönster publish an official cleaning guide?

Svenska Fönster has not published an official cleaning guide. The protocol on this page is based on Justin Orloff's hands-on experience since 1999.

Can I use a water-fed pole on Svenska Fönster windows?

In my experience, yes: purified water via a water-fed pole is one of the safest methods for Svenska Fönster glass. Ensure TDS is at or near zero before use and avoid directing high-pressure water at seals or gaskets.

Field Notes

“Svenska Fönster renovation windows sometimes sit in reveals built for older, thicker frames. This creates shadow gaps and deep sills that collect leaves, moss and debris. Add sill clearing to the standard clean on any property over 15 years old.”

Justin Orloff

What's next for you?

The Skill

New to window cleaning?

Start with the core techniques before tackling premium systems.

Start The Skill, $69

The Standard

Upskill your team

Covers every system, product type, and tricky scenario.

Train your team, $199 per person

Do you make windows, doors or glazing?

The brands here are not partners. We wrote these care guides ourselves, so your customers know how to look after your windows. Want your own?

Become a Brand Partner

Brand logos provided by Logo.dev