Asia-Pacific ยท Window Manufacturer
Fenesta: Window Cleaning Guide
๐ฎ๐ณ India ยท Last reviewed by Justin Orloff
For owners, installers and cleaners looking after Fenesta windows. The maker's own care advice first, then what I add as a window cleaner since 1999.

Quick Facts
- Founded
- 2003
- HQ
- Gurugram, India
- Parent
- DCM Shriram Group
- Materials
- uPVC, aluminium
- Specialty
- Vertically integrated supply and installation
- Market
- India residential and light commercial
Brand at a Glance

- India's largest branded window company with presence in 350+ cities
- Full vertical integration: extrusion, fabrication, installation, service
- uPVC and aluminium systems designed for Indian climate zones
- Official website
- www.fenesta.com
Product Range
- uPVC casement and sliding windows (standard residential range)
- Aluminium sliding and casement windows (commercial and premium residential)
- uPVC and aluminium doors including sliding and French door configurations
Why This System
Fenesta controls quality from raw profile to installed window - rare in India's fragmented market. Their national service network means replacement seals and hardware are more accessible than for imported systems. The brand sits at the premium end of India's domestic window market.
Fenesta uPVC profiles are sensitive to abrasive cleaners and high-alkaline detergents. India's dust, monsoon grime, and UV combine to create a cleaning challenge: surface soiling is heavy, but the profiles need gentle handling. Aluminium frames on coastal installations will carry salt residue that accelerates corrosion if left on frame joints and weep holes.
Step 1 of 2: Manufacturer Recommendations
Official Care Guidance
No official guide published. The steps below are based on Justin Orloff's hands-on experience since 1999 with this system.
Step 2 of 2: The Orloffs Protocol
The Orloffs Protocol
Since 1999 I've cleaned hundreds, if not thousands, of different window brands and systems. The physics of clean glass don't change from one brand to the next. Follow the steps below and you'll clean your Fenesta windows to a professional standard, guaranteed.
Follow these steps in order. Each one builds on the last. This is the same sequence I use on every Fenesta installation.
Pro Tools
My daily tool list. This is what I carry to every job.
- 1Microfiber T-bar applicator, kept clean and rinsed regularly to prevent grit
- 2Professional squeegee with a fresh rubber blade
- 3Extension pole for glass above arm height
- 4Bucket with at least 10 litres of water and enough soap for cleaning power without excess foam
- 5100% cotton towelling rags for edge detailing
- 6Vacuum for sill tracks and base profiles
Preparation: before any water touches the glass
Fill the bucket with at least 10 litres of water. Add soap for cleaning power: enough to cut through environmental deposits, not so much you are fighting foam.
Before touching the glass, brush down the surface to remove loose dust, spiderwebs, and debris. Any grit left on the glass during the wash phase risks scratching during agitation.
Check the aluminium frame condition before you start. Confirm which cleaning product is safe for that surface before opening any bottle.
Cover anything below the windows that cannot be moved.

Agitation: apply and work the solution
Dip the microfiber T-bar completely into the soap water, both sides. Remove excess water with your hand so it does not drip. Apply the solution across the entire glass surface with overlapping passes.
The goal is to fully dissolve and release every deposit from the glass surface. Anything not released during agitation gets transported across the glass by the squeegee as a smear.
For stubborn spots (insect marks, salt residue, environmental deposits), re-apply soap water and allow it to soak for a full minute before agitating again. Use more soap water, not more pressure.
For panels above arm reach: attach the T-bar to an extension pole. Work in sections (top first, then middle, then bottom), keeping each section wet until you squeegee it.
Rinse the T-bar cover regularly during the job. A dirty applicator causes microscopic scratches that accumulate over time.

Detail the frame edge before squeegeeing
Use your 100% cotton towelling rag, finger pressed into the fabric, to work into every junction and remove pooled soap water before the squeegee pass.
This prevents drips running down onto already-cleaned areas during squeegeeing and keeps soap water out of drainage channels.
On Fenesta aluminium frames, pay particular attention to the bottom edge where glass meets the frame sill: water pooled here runs into drainage openings and leaves residue over time.

The squeegee
Tilt the squeegee at a slight angle so soap water spills from one side of the channel only, not both. If the rubber is jumping or squeaking, either the rubber is not lubricated enough or the glass surface has warmed.
Cutting in: start with the rubber blade making first contact on a dry edge of the glass.
Side to side: horizontal passes across the panel. Works well on wide sections. Top to bottom: vertical passes down the panel. Works well on tall narrow sections.
The J turn: one smooth unbroken motion top to bottom, wrist rotating at each end to reverse without lifting the rubber. The most efficient method on larger panels, but it requires training before applying it to premium glass.
Wipe the rubber dry after every pass. Overlap each stroke by 2-3 cm.

Final edge detailing
After squeegeeing, there is always a residual line of water along the bottom edge and at the panel sides. Take a dry cotton rag, fold to a clean corner, and detail these edges in one smooth pass.
On Fenesta frames, the bottom edge where glass meets the sill requires the most careful attention. Water left here runs into drainage and leaves residue that affects the next clean.
Rotate the rag to a clean section after every pass. If the rag picks up grit at any point, replace it immediately.

Frame wipe and hardware check
On Fenesta powder-coated aluminium frames: use pH-neutral cleaner only, never abrasive pads or steel wool. Dry immediately after wiping.
Check that all drainage openings are clear and unobstructed. Water must be able to flow freely: a blocked channel leads to accumulation that affects seal performance over time.
Operate every opening window through its full range. Stiff handles or resistance at locking points indicate hardware that needs lubrication. Flag it to the owner rather than forcing it.

Pro Tips
- Never clean in direct midday sun - India's UV dries solution before you can squeegee, leaving streaks.
- Monsoon season: increase frequency to monthly - fungal growth on seals is common in high-humidity zones.
- Use a cotton bud or soft brush on interlock channels - dust packs into sliding window tracks and causes seal wear.
What NOT To Do
- Do not use abrasive pads or scouring powder on uPVC profiles - surface scratches trap dirt and degrade UV resistance.
- Do not use solvent-based cleaners near rubber seals - seals dry out and crack.
- Do not pressure wash directly into frame joints - forces water past seals into the wall cavity.
Bundle Kit
Pro Kit
The full professional setup. Brass squeegees, T-bar with applicator cover, tool belt, rags, soap, and bucket. Everything from the daily tool list in one box.
Cleaning Frequency
Every 6-8 weeks in inland cities; monthly on coastal or high-pollution sites. Post-monsoon deep clean is essential.
Frequently Asked Questions
How often should I clean Fenesta windows?
For Fenesta windows, Every 6-8 weeks in inland cities; monthly on coastal or high-pollution sites. Post-monsoon deep clean is essential.. City locations may need more frequent cleaning.
What tools do I need for Fenesta windows?
Professional cleaning of Fenesta windows requires my daily tool list of: Microfiber T-bar applicator, kept clean and rinsed regularly to prevent grit, Professional squeegee with a fresh rubber blade, Extension pole for glass above arm height, Bucket with at least 10 litres of water and enough soap for cleaning power without excess foam, 100% cotton towelling rags for edge detailing, Vacuum for sill tracks and base profiles.
What should I avoid on Fenesta windows?
Do not use abrasive pads or scouring powder on uPVC profiles - surface scratches trap dirt and degrade UV resistance.
Does Fenesta publish an official cleaning guide?
Fenesta has not published an official cleaning guide. The protocol on this page is based on Justin Orloff's hands-on experience since 1999.
Can I use a water-fed pole on Fenesta windows?
In my experience, yes: purified water via a water-fed pole is one of the safest methods for Fenesta glass. Ensure TDS is at or near zero before use and avoid directing high-pressure water at seals or gaskets.
Field Notes
โIn Delhi and NCR, winter fog combined with dust creates a cement-like film on glass. Soak the glass for 30 seconds before squeegeeing - do not scrape dry. In Mumbai and coastal Maharashtra, salt air attacks aluminium frame joints - check and clear weep holes every visit.โ
What's next for you?
The Skill
New to window cleaning?
Start with the core techniques before tackling premium systems.
Start The Skill, $69The Standard
Upskill your team
Covers every system, product type, and tricky scenario.
Train your team, $199 per personDo you make windows, doors or glazing?
The brands here are not partners. We wrote these care guides ourselves, so your customers know how to look after your windows. Want your own?
Become a Brand PartnerBrand logos provided by Logo.dev