Europe Β· Hardware Manufacturer
Stac: Window Cleaning Guide
πͺπΈ Spain Β· Last reviewed by Justin Orloff
For owners, installers and cleaners looking after Stac windows. The maker's own care advice first, then what I add as a window cleaner since 1999.

Brand at a Glance
- Country
- Spain
- Products
- Window and door hardware, locking systems, fittings
- Market
- Spanish and European window fabricators
- Website
- stac.es
Product Range
- Locking Systems
- Handles and Fittings
- Tilt-Turn Hardware
Why This System
Hardware brand - the primary consideration is protecting Stac fittings from cleaning product contact during window cleaning. Multi-point locking mechanisms have exposed metal components at the frame rebate - keep cleaning products off these. Handle and hinge finishes vary - chrome, brushed nickel, black - use appropriate care.
Step 1 of 2: Manufacturer Recommendations
Official Care Guidance
No official guide published. The steps below are based on Justin Orloff's hands-on experience since 1999 with this system.
Step 2 of 2: The Orloffs Protocol
The Orloffs Protocol
This is how I clean Stac windows. The tools and technique below come from daily professional work on the glass since 1999. Every step has been tested on real installations and adapted specifically for Stac systems.
Follow these steps in order. Each one builds on the last. This is the same sequence I use on every Stac installation.
Pro Tools
My daily tool list. This is what I carry to every job.
- 1Microfiber T-bar applicator, kept clean and rinsed regularly to prevent grit
- 2Professional squeegee with a fresh rubber blade
- 3Extension pole for glass above arm height
- 4Bucket with at least 10 litres of water and enough soap for cleaning power without excess foam
- 5100% cotton towelling rags for edge detailing
- 6Vacuum for sill tracks and base profiles
Preparation: before any water touches the glass
Fill the bucket with at least 10 litres of water. Add soap for cleaning power: enough to cut through environmental deposits, not so much you are fighting foam.
Before touching the glass, brush down the surface to remove loose dust, spiderwebs, and debris. Any grit left on the glass during the wash phase risks scratching during agitation.
Check the aluminium frame condition before you start. Confirm which cleaning product is safe for that surface before opening any bottle.
Cover anything below the windows that cannot be moved.

Agitation: apply and work the solution
Dip the microfiber T-bar completely into the soap water, both sides. Remove excess water with your hand so it does not drip. Apply the solution across the entire glass surface with overlapping passes.
The goal is to fully dissolve and release every deposit from the glass surface. Anything not released during agitation gets transported across the glass by the squeegee as a smear.
For stubborn spots (insect marks, salt residue, environmental deposits), re-apply soap water and allow it to soak for a full minute before agitating again. Use more soap water, not more pressure.
For panels above arm reach: attach the T-bar to an extension pole. Work in sections (top first, then middle, then bottom), keeping each section wet until you squeegee it.
Rinse the T-bar cover regularly during the job. A dirty applicator causes microscopic scratches that accumulate over time.

Detail the frame edge before squeegeeing
Use your 100% cotton towelling rag, finger pressed into the fabric, to work into every junction and remove pooled soap water before the squeegee pass.
This prevents drips running down onto already-cleaned areas during squeegeeing and keeps soap water out of drainage channels.
On STAC aluminium frames, pay particular attention to the bottom edge where glass meets the frame sill: water pooled here runs into drainage openings and leaves residue over time.

The squeegee
Tilt the squeegee at a slight angle so soap water spills from one side of the channel only, not both. If the rubber is jumping or squeaking, either the rubber is not lubricated enough or the glass surface has warmed.
Cutting in: start with the rubber blade making first contact on a dry edge of the glass.
Side to side: horizontal passes across the panel. Works well on wide sections. Top to bottom: vertical passes down the panel. Works well on tall narrow sections.
The J turn: one smooth unbroken motion top to bottom, wrist rotating at each end to reverse without lifting the rubber. The most efficient method on larger panels, but it requires training before applying it to premium glass.
Wipe the rubber dry after every pass. Overlap each stroke by 2-3 cm.

Final edge detailing
After squeegeeing, there is always a residual line of water along the bottom edge and at the panel sides. Take a dry cotton rag, fold to a clean corner, and detail these edges in one smooth pass.
On STAC frames, the bottom edge where glass meets the sill requires the most careful attention. Water left here runs into drainage and leaves residue that affects the next clean.
Rotate the rag to a clean section after every pass. If the rag picks up grit at any point, replace it immediately.

Frame wipe and hardware check
On STAC powder-coated aluminium frames: use pH-neutral cleaner only, never abrasive pads or steel wool. Dry immediately after wiping.
Check that all drainage openings are clear and unobstructed. Water must be able to flow freely: a blocked channel leads to accumulation that affects seal performance over time.
Operate every opening window through its full range. Stiff handles or resistance at locking points indicate hardware that needs lubrication. Flag it to the owner rather than forcing it.

What NOT To Do
- No cleaning products left in contact with locking mechanisms.
- No acid or solvent cleaners near hardware fittings.
- Do not allow soap solution to pool around hinge positions.
Bundle Kit
Pro Kit
The full professional setup. Brass squeegees, T-bar with applicator cover, tool belt, rags, soap, and bucket. Everything from the daily tool list in one box.
Cleaning Frequency
Clean every 4β8 weeks depending on environment.
Frequently Asked Questions
How often should I clean Stac windows?
For Stac windows, I recommend cleaning twice a year depending on your local environment. City locations may need more frequent cleaning.
What tools do I need for Stac windows?
Professional cleaning of Stac windows requires my daily tool list of: Microfiber T-bar applicator, kept clean and rinsed regularly to prevent grit, Professional squeegee with a fresh rubber blade, Extension pole for glass above arm height, Bucket with at least 10 litres of water and enough soap for cleaning power without excess foam, 100% cotton towelling rags for edge detailing, Vacuum for sill tracks and base profiles.
What should I avoid on Stac windows?
No cleaning products left in contact with locking mechanisms.
Does Stac publish an official cleaning guide?
Stac has not published an official cleaning guide. The protocol on this page is based on Justin Orloff's hands-on experience since 1999.
Can I use a water-fed pole on Stac windows?
In my experience, yes: purified water via a water-fed pole is one of the safest methods for Stac glass. Ensure TDS is at or near zero before use and avoid directing high-pressure water at seals or gaskets.
Field Notes
βWell-maintained hardware runs more smoothly and lasts longer. A quick dry-wipe of handles and visible lock components at each clean takes thirty seconds and extends the fitting life significantly.β
What's next for you?
The Skill
New to window cleaning?
Start with the core techniques before tackling premium systems.
Start The Skill, $69The Standard
Upskill your team
Covers every system, product type, and tricky scenario.
Train your team, $199 per personDo you make windows, doors or glazing?
The brands here are not partners. We wrote these care guides ourselves, so your customers know how to look after your windows. Want your own?
Become a Brand PartnerBrand logos provided by Logo.dev