Skip to content
ALUMISR logo

Middle East ยท Profile System

ALUMISR: Window Cleaning Guide

๐Ÿ‡ช๐Ÿ‡ฌ Egypt ยท Last reviewed by Justin Orloff

For owners, installers and cleaners looking after ALUMISR windows. The maker's own care advice first, then what I add as a window cleaner since 1999.

See the 6 steps

A squeegee pulling soap water off a window, with a harbour behind the glass

Brand at a Glance

Founded
Established Egyptian manufacturer
HQ
Cairo, Egypt
Materials
Aluminium profiles and window systems
Market position
Egyptian aluminium profiles and glazing systems supplier
Certifications
Egyptian standards compliance
Regions served
Egypt, Middle East, North Africa
Official website
alumisr.com

Product Range

  • Aluminium casement windows
  • Sliding window systems
  • Curtain wall profiles
  • Aluminium doors

Why This System

Manufactured and distributed within Egypt for the regional construction market. Aluminium profiles in this climate category face specific challenges from desert dust, salt air on coastal sites, and high UV intensity. Products span residential, commercial, and hospitality sectors in Egypt and regional export markets. Local availability of profiles and fabrication reduces lead times for Egyptian projects.

Aluminium windows in Egypt and the MENA region face unique deposit types: mineral-rich Saharan dust, salt from coastal humidity, and baked-on residue from high temperatures. These deposits require pre-rinsing before any applicator touches the glass - dry wiping in dusty conditions scratches glass. The approach is pre-rinse, agitate, squeegee, detail. No shortcuts.

Step 1 of 2: Manufacturer Recommendations

Official Care Guidance

No official guide published. The steps below are based on Justin Orloff's hands-on experience since 1999 with this system.

Step 2 of 2: The Orloffs Protocol

The Orloffs Protocol

Since 1999 I've cleaned hundreds, if not thousands, of different window brands and systems. The physics of clean glass don't change from one brand to the next. Follow the steps below and you'll clean your ALUMISR windows to a professional standard, guaranteed.

Follow these steps in order. Each one builds on the last. This is the same sequence I use on every ALUMISR installation.

Pro Tools

My daily tool list. This is what I carry to every job.

  1. 1Microfiber T-bar applicator, kept clean and rinsed regularly to prevent grit
  2. 2Professional squeegee with a fresh rubber blade
  3. 3Extension pole for glass above arm height
  4. 4Bucket with at least 10 litres of water and enough soap for cleaning power without excess foam
  5. 5100% cotton towelling rags for edge detailing
  6. 6Vacuum for sill tracks and base profiles
  1. Preparation: before any water touches the glass

    Fill the bucket with at least 10 litres of water. Add soap for cleaning power: enough to cut through environmental deposits, not so much you are fighting foam.

    Before touching the glass, brush down the surface to remove loose dust, spiderwebs, and debris. Any grit left on the glass during the wash phase risks scratching during agitation.

    Check the aluminium frame condition before you start. Confirm which cleaning product is safe for that surface before opening any bottle.

    Cover anything below the windows that cannot be moved.

    Window cleaning tools laid out ready: squeegee, brass channel and washer sleeves
  2. Agitation: apply and work the solution

    Dip the microfiber T-bar completely into the soap water, both sides. Remove excess water with your hand so it does not drip. Apply the solution across the entire glass surface with overlapping passes.

    The goal is to fully dissolve and release every deposit from the glass surface. Anything not released during agitation gets transported across the glass by the squeegee as a smear.

    For stubborn spots (insect marks, salt residue, environmental deposits), re-apply soap water and allow it to soak for a full minute before agitating again. Use more soap water, not more pressure.

    For panels above arm reach: attach the T-bar to an extension pole. Work in sections (top first, then middle, then bottom), keeping each section wet until you squeegee it.

    Rinse the T-bar cover regularly during the job. A dirty applicator causes microscopic scratches that accumulate over time.

    Washing the glass with a soaked sleeve to lift and release the dirt
  3. Detail the frame edge before squeegeeing

    Use your 100% cotton towelling rag, finger pressed into the fabric, to work into every junction and remove pooled soap water before the squeegee pass.

    This prevents drips running down onto already-cleaned areas during squeegeeing and keeps soap water out of drainage channels.

    On Alumisr aluminium frames, pay particular attention to the bottom edge where glass meets the frame sill: water pooled here runs into drainage openings and leaves residue over time.

    Detailing the frame edge with a cloth before the squeegee pass
  4. The squeegee

    Tilt the squeegee at a slight angle so soap water spills from one side of the channel only, not both. If the rubber is jumping or squeaking, either the rubber is not lubricated enough or the glass surface has warmed.

    Cutting in: start with the rubber blade making first contact on a dry edge of the glass.

    Side to side: horizontal passes across the panel. Works well on wide sections. Top to bottom: vertical passes down the panel. Works well on tall narrow sections.

    The J turn: one smooth unbroken motion top to bottom, wrist rotating at each end to reverse without lifting the rubber. The most efficient method on larger panels, but it requires training before applying it to premium glass.

    Wipe the rubber dry after every pass. Overlap each stroke by 2-3 cm.

    Pulling the squeegee across the wet glass in one clean stroke
  5. Final edge detailing

    After squeegeeing, there is always a residual line of water along the bottom edge and at the panel sides. Take a dry cotton rag, fold to a clean corner, and detail these edges in one smooth pass.

    On Alumisr frames, the bottom edge where glass meets the sill requires the most careful attention. Water left here runs into drainage and leaves residue that affects the next clean.

    Rotate the rag to a clean section after every pass. If the rag picks up grit at any point, replace it immediately.

    Wiping the final edge of the glass with a dry cloth
  6. Frame wipe and hardware check

    On Alumisr powder-coated aluminium frames: use pH-neutral cleaner only, never abrasive pads or steel wool. Dry immediately after wiping.

    Check that all drainage openings are clear and unobstructed. Water must be able to flow freely: a blocked channel leads to accumulation that affects seal performance over time.

    Operate every opening window through its full range. Stiff handles or resistance at locking points indicate hardware that needs lubrication. Flag it to the owner rather than forcing it.

    The finished, streak-free window after the full Orloffs Protocol

Pro Tips

  • Always pre-rinse before agitating in dusty Middle East conditions - dry wiping silica dust scratches glass.
  • Rinse sill channels thoroughly in coastal Egyptian locations to remove salt accumulation.
  • Vacuum sill tracks before any water touches the glass - dust and water create abrasive paste.
  • Never clean in direct sunlight in high-UV Egyptian conditions - solution flashes off within seconds on heated glass.

What NOT To Do

  • Do not wipe dusty glass dry - pre-rinse first to prevent silica scratching.
  • Do not use alkaline or acid cleaners on aluminium profiles.
  • Do not clean in direct sunlight - solution evaporates before you can squeegee it.
  • Do not ignore blocked weep holes - they cause water back-up in dusty environments.

Bundle Kit

Pro Kit

The full professional setup. Brass squeegees, T-bar with applicator cover, tool belt, rags, soap, and bucket. Everything from the daily tool list in one box.

Cleaning Frequency

Glass and frames
4-6ร— per yearHigher in dusty or coastal locations.
Sill track and drainage
Every clean
Coastal salt rinse
Every cleanEssential in Alexandria and Red Sea coastal areas.

Frequently Asked Questions

How often should I clean ALUMISR windows?

For ALUMISR windows, Glass and frames: 4-6ร— per year (Higher in dusty or coastal locations.). Sill track and drainage: Every clean. Coastal salt rinse: Every clean (Essential in Alexandria and Red Sea coastal areas.). City locations may need more frequent cleaning.

What tools do I need for ALUMISR windows?

Professional cleaning of ALUMISR windows requires my daily tool list of: Microfiber T-bar applicator, kept clean and rinsed regularly to prevent grit, Professional squeegee with a fresh rubber blade, Extension pole for glass above arm height, Bucket with at least 10 litres of water and enough soap for cleaning power without excess foam, 100% cotton towelling rags for edge detailing, Vacuum for sill tracks and base profiles.

What should I avoid on ALUMISR windows?

Do not wipe dusty glass dry - pre-rinse first to prevent silica scratching.

Does ALUMISR publish an official cleaning guide?

ALUMISR has not published an official cleaning guide. The protocol on this page is based on Justin Orloff's hands-on experience since 1999.

Can I use a water-fed pole on ALUMISR windows?

In my experience, yes: purified water via a water-fed pole is one of the safest methods for ALUMISR glass. Ensure TDS is at or near zero before use and avoid directing high-pressure water at seals or gaskets.

Field Notes

โ€œALUMISR profiles are used across Cairo's residential and commercial construction market. On high-rise buildings in Cairo and the New Cairo developments, access requires scaffolding or cradle. The most common deposit types on these windows are mineral-rich Nile-valley dust and, near the Mediterranean, sea salt. Annual deep cleans with longer agitation time are more effective than frequent surface wipes in this environment.โ€

Justin Orloff

What's next for you?

The Skill

New to window cleaning?

Start with the core techniques before tackling premium systems.

Start The Skill, $69

The Standard

Upskill your team

Covers every system, product type, and tricky scenario.

Train your team, $199 per person

Do you make windows, doors or glazing?

The brands here are not partners. We wrote these care guides ourselves, so your customers know how to look after your windows. Want your own?

Become a Brand Partner

Brand logos provided by Logo.dev